MISUMIS START
Automation Components
Rotary Motion
Rotary Shafts, Drive Shafts
Drive Shafts
Motor shafts / two-sided offset / machining selectable

Filtreringsvillkor

Hardness
- No Hardened
Surface Treatment
No Surface Treatment
Surface Treatment Provided
Black Oxide
Electroless Nickel Plating
Shaft Dia. D(mm)
- 10
- 12
- 15
- 20
- 25
- 30
- 35
- 40
- 50
Shaft Tolerance
- h6
- h7
L(mm)
[50-500/0.5mm units]
LA(mm)
[4-150/0.5mm units]
LB(mm)
[4-70/0.5mm units]
P(mm)
- 6
- 8
- 10
- 12
- 15
- 17
- 20
- 25
- 30
- 35
- 40
- 45
Type
- KZCC
- KZCE
- KZCF
- KZCN
- KZCP
CAD
- 2D
Uppskattade leveransdagar
- Alla
- Inom 9 arbetsdagar
- Inom 17 arbetsdagar
- Inom 19 arbetsdagar
- Inom 29 arbetsdagar

MISUMI

Motor shafts / two-sided offset / machining selectable

KatalogS.1-873

Artikelnummer:

Ej färdigt: 42 kandidater hittades.

Skiss och specifikationstabell
Artikelnummerlista
Detaljerad information
Katalog

Skiss och specifikationstabell

Dimensional Drawing

Driving Shaft - Both Ends Stepped: Related Image

[ ! ]LA+LB ≤ L/2
[ ! ]ℓ = L－ (LA+LB)
[!] The shaft may have centering holes on ends.
[!] There is an undercut 1.5 mm or less in width and 0.3 mm or less in depth on the stepped part.
[!] Step P of KZCE has no grinding undercut. Step R = 0.2 or Less
* Ds: Tap dimension of Bearing Inner Race.

D	Tolerance
	h7	h6
10	0 -0.015	0 -0.009
12	0 -0.018	0 -0.011
15
20	0 -0.021	0 -0.013
25
30
35	—	0 -0.016
40
50

D	Circularity M
	KZCE	Others
10	0.004	0.003
12
15	0.005
20
25	0.006	0.005
30
35	—
40
50

Type	D, P Tolerance	Concentricity	Perpendicularity	[M] Material	[H]Hardness	[S] Surface Treatment
KZCE	h7	⌀0.05	⊥0.05	EN 1.1191 Equiv.	—	Black Oxide
KZCN	h6	⌀0.01	⊥0.01	EN 1.1191 Equiv.	—	—
KZCC						Black Oxide
KZCP						Electroless Nickel Plating
KZCF				EN 1.1191 Equiv.	Induction Hardened	—
KZCF				EN 1.1191 Equiv.	Surface Hardness 50HRC or more	—

Specification Table

Part Number	—	L	—	P	—	LA	—	LB
KZCF50	—	450	—	P45	—	LA80	—	LB50

Part Number		0.5 mm Increments	Selection	0.5 mm Increments		* Ds
Type	D	L	P	LA	LB
KZCE (D10 to 30) KZCN KZCC KZCP KZCF	10	50.0 to 300.0	6	4.0 to 40.0	4.0 to 40.0	8
			8			9.5
	12		8			10
			10	5.0 to 50.0	5.0 to 50.0	11.5
	15	100.0 to 400.0	10			13
			12	5.0 to 75.0		14
	20		15			18
			17	5.0 to 100.0		19
	25	100.0 to 500.0	17			21
			20	10.0 to 100.0	10.0 to 60.0	24
	30		20			27
			25	10.0 to 125.0		29
	* 35		25			31
			30	15.0 to 150.0	15.0 to 70.0	34
	* 40	200.0 to 500.0	30			37
			35			39
	* 50		40	20.0 to 150.0	20.0 to 70.0	48
			45			49

[!] * marked sizes are not available for KZCE.

Alterations

Part Number	—	L	—	P	—	LA	—	LB	—	(MA, NA, KA, TA, SA, WA, etc.)
KZCF40	—	300	—	P30	—	LA60	—	LB60	—	NB12 － TA40 － WB10 － GB20 － AB90

Alterations

Code

Spec.

Left End

Middle

Right End

Threaded Ends

MA
MSA
MMA

Left End
MC
MSC
MMC
Right End
MD
MSD
MMD

MB
MSB
MMB

Adds threads at shaft ends. Specify the length of the threads. (Accuracy, coarse or fine threads differ depending on the current ordering code.)
Ordering Code MA15-MSB15 1 mm Increments 5 ≤ Thread Length ≤ M × 5, LA (LB)-2

Code				Screw Accuracy
Left, Middle		Right, Middle		Screw Accuracy
MA	MC	MB	MD	Coarse	JIS 6h (Class 2)
MSA	MSC	MSB	MSD	Fine (Standard Grade)	JIS 6h (Class 2)
MMA	MMC	MMB	MMD	Fine (Precision Grade)	JIS 4h (Class 1)

[!] When D,P = M, thread length can be specified.
[NG] Fine (Precision Grade) is not available for KZCE.

M (Coarse)	Pitch	M (Fine)	Pitch	M (Fine)	Pitch
M6	1.0	M6	0.75	M25	1.5
M8	1,25	M8	0.75	M30	1.5
M10	1.5	M10	0.75	M35	1.5
M12	1.75	M12	1.0	M40	1.5
M20	2.5	M15	1.0	M45	1.5
M30	3.5	M17	1.0	M50	1.5
		M20	1.0

Tapped Ends

—

Adds taps on shaft ends. Select the thread diameter.
Ordering Code NA5-NB5 [!] NA, NB ≤ P-4

NA (Coarse), NB (Coarse)
Selection

M3 M4 M5 M6 M8
M10 M12 M16 M20
M24

Keyway Machining

KC
KD

Adds a keyway. Specify the position and the length of the keyway.
Ordering Code KA10-HA30-KB100-HB50
KA, HA, KB, HB, KC, HC, KD, HD = 1 mm Increments
[ ! ]3 ≤ HA,HB,HC,HD ≤ 100
[!]When more than 2 keyways are added, the tolerances may shift by up to 0.2°.
[!] Specify the keyway position more than 2 mm away from the stepped part.

Keyway Machining + Set Screw Flat

ZC
ZD

Adds a flat at any designated angle based on the keyways. Specify the position and the length for each keyway, and the angle for the set screw flats.
Ordering CodeZA40-HA20-AA90
ZA, HA, ZB, HB, ZC, HC, ZD, HD = 1 mm Increments AA, AB, AC, AD = 30° Increments 30° ≤ AA, AB, AC, AD ≤ 330°
[!] HA, HB, HC, HD ≤ 100 [!]Specify the keyway position more than 2 mm away from the stepped part.

·Specification Code

Keyway Position Specified	Keyway Width Specified	Angle Configurable
Keyway Position Specified	Keyway Width Specified	30° Increments
ZA	HA	AA
ZB	HB	AB
ZC	HC	AC
ZD	HD	AD

D·P	6 to 17	20 to 40	45·50
H	1	2	3

[!] The length of each set screw flat is the same as that of each keyway.
[!] For a keyway and the angle of a set screw flat, the tolerances may shift by up to ± 0.2°.

Retaining Ring Groove

TC
TD

Adds a retaining ring groove. Specify the position of a retaining ring groove.
Ordering Code TA10－TB10
TA, TB = 1 mm Increments 4 ≤ TA (TB) ≤ LA (LB)-3
[!] Retaining rings are included.

P = 6,8: Retaining Ring Type E P ≥ 10, D ≥ 10: Retaining Ring Type C

Driving Shafts			Retaining Ring
[M] Material	[H]Hardness	[S] Surface Treatment	[M] Material
EN 1.1191 Equiv.	—	—	Spring Steel
		Black Oxide	Spring Steel
		Electroless Nickel Plating	EN 1.4301 Equiv. (CSP)
	Surface 50HRC or more	—	Spring Steel

Wrench Flats

Adds wrench flats. Specify the position of a wrench flat.
Ordering Code SA5 SA, SB, SD = 1 mm Increments SA, SB, SD ≥ 0 SA ≤ LA-ℓ, SB ≤ LB-ℓ, SD ≤ L-LA-LB-ℓ

D	10	12	15	20	25	30	35	40	50
W	8	10	13	17	22	27	30	36	41
ℓ	8	10				15		20

P	6	8·10	12	15	17	20	25	30	35	40	45
W₁	5	7	10	13	14	17	19	27	30	36	38
ℓ	8		10					15		20

2 Set Screw Flats (Angle Specified)

Adds a flat at any designated angle besides the datum plane 0°.
Specify the position, the length and the angle of the set screw flats. When 0° is specified, only one set screw flat is machinable.
Ordering Code WA15-GA10-AA0
WA, WB, WC, GA, GB, GC = 1 mm Increments AA, AB, AC = 30° Increments, 0° ≤ AA, AB, AC ≤ 330°

·Specification Code

Set Screw Flat Position Specification	Set Screw Flat Width Specification	Angle Configurable
Set Screw Flat Position Specification	Set Screw Flat Width Specification	30° Increments
WA	GA	AA
WB	GB	AB
WC	GC	AC

D·P	6 to 17	20 to 40	45·50
H	1	2	3

Tolerance Change

PJ (js6)
PK (k6)

Changes the tolerance of P Dimension of the stepped part to js6 or k6.
Ordering Code PJ or PK
[!] Both LA and LB tolerances will be changed.
[NG] Not available for KZCE.

·About KZCF (Induction Hardened)

When alterations on the above are specified,
the shafts are induction hardened after machining. (Except the threaded sections)
As a result, these may occur:
(1): Due to thermal conduction to the thread, the threads may be hardened by 2 to 3 mm. (2): Induction Hardened may shrink the keyway width (Around -0.01 to -0.02)
If the key becomes hard to fit, adjust it by gauging.

Artikelnummerlista

Antal artiklar

Artikelnummer

KZCC10-[50-300/0.5]-P[6,8]-LA[4-40/0.5]-LB[4-40/0.5]

KZCC12-[50-300/0.5]-P[8,10]-LA[4-50/0.5]-LB[4-50/0.5]

KZCC15-[100-400/0.5]-P[10,12]-LA[5-75/0.5]-LB[5-50/0.5]

KZCC20-[100-400/0.5]-P[15,17]-LA[5-100/0.5]-LB[5-50/0.5]

KZCC25-[100-500/0.5]-P[17,20]-LA[5-100/0.5]-LB[5-60/0.5]

KZCC30-[100-500/0.5]-P[20,25]-LA[10-125/0.5]-LB[10-60/0.5]

KZCC35-[100-500/0.5]-P[25,30]-LA[10-150/0.5]-LB[10-70/0.5]

KZCC40-[200-500/0.5]-P[30,35]-LA[15-150/0.5]-LB[15-70/0.5]

KZCC50-[200-500/0.5]-P[40,45]-LA[20-150/0.5]-LB[20-70/0.5]

KZCE10-[50-300/0.5]-P[6,8]-LA[4-40/0.5]-LB[4-40/0.5]

KZCE12-[50-300/0.5]-P[8,10]-LA[4-50/0.5]-LB[4-50/0.5]

KZCE15-[100-400/0.5]-P[10,12]-LA[5-75/0.5]-LB[5-50/0.5]

KZCE20-[100-400/0.5]-P[15,17]-LA[5-100/0.5]-LB[5-50/0.5]

KZCE25-[100-500/0.5]-P[17,20]-LA[5-100/0.5]-LB[5-60/0.5]

KZCE30-[100-500/0.5]-P[20,25]-LA[10-125/0.5]-LB[10-60/0.5]

KZCF10-[50-300/0.5]-P[6,8]-LA[4-40/0.5]-LB[4-40/0.5]

KZCF12-[50-300/0.5]-P[8,10]-LA[4-50/0.5]-LB[4-50/0.5]

KZCF15-[100-400/0.5]-P[10,12]-LA[5-75/0.5]-LB[5-50/0.5]

KZCF20-[100-400/0.5]-P[15,17]-LA[5-100/0.5]-LB[5-50/0.5]

KZCF25-[100-500/0.5]-P[17,20]-LA[5-100/0.5]-LB[5-60/0.5]

KZCF30-[100-500/0.5]-P[20,25]-LA[10-125/0.5]-LB[10-60/0.5]

KZCF35-[100-500/0.5]-P[25,30]-LA[10-150/0.5]-LB[10-70/0.5]

KZCF40-[200-500/0.5]-P[30,35]-LA[15-150/0.5]-LB[15-70/0.5]

KZCF50-[200-500/0.5]-P[40,45]-LA[20-150/0.5]-LB[20-70/0.5]

KZCN10-[50-300/0.5]-P[6,8]-LA[4-40/0.5]-LB[4-40/0.5]

KZCN12-[50-300/0.5]-P[8,10]-LA[4-50/0.5]-LB[4-50/0.5]

KZCN15-[100-400/0.5]-P[10,12]-LA[5-75/0.5]-LB[5-50/0.5]

KZCN20-[100-400/0.5]-P[15,17]-LA[5-100/0.5]-LB[5-50/0.5]

KZCN25-[100-500/0.5]-P[17,20]-LA[5-100/0.5]-LB[5-60/0.5]

KZCN30-[100-500/0.5]-P[20,25]-LA[10-125/0.5]-LB[10-60/0.5]

KZCN35-[100-500/0.5]-P[25,30]-LA[10-150/0.5]-LB[10-70/0.5]

KZCN40-[200-500/0.5]-P[30,35]-LA[15-150/0.5]-LB[15-70/0.5]

KZCN50-[200-500/0.5]-P[40,45]-LA[20-150/0.5]-LB[20-70/0.5]

KZCP10-[50-300/0.5]-P[6,8]-LA[4-40/0.5]-LB[4-40/0.5]

KZCP12-[50-300/0.5]-P[8,10]-LA[4-50/0.5]-LB[4-50/0.5]

KZCP15-[100-400/0.5]-P[10,12]-LA[5-75/0.5]-LB[5-50/0.5]

KZCP20-[100-400/0.5]-P[15,17]-LA[5-100/0.5]-LB[5-50/0.5]

KZCP25-[100-500/0.5]-P[17,20]-LA[5-100/0.5]-LB[5-60/0.5]

KZCP30-[100-500/0.5]-P[20,25]-LA[10-125/0.5]-LB[10-60/0.5]

KZCP35-[100-500/0.5]-P[25,30]-LA[10-150/0.5]-LB[10-70/0.5]

KZCP40-[200-500/0.5]-P[30,35]-LA[15-150/0.5]-LB[15-70/0.5]

KZCP50-[200-500/0.5]-P[40,45]-LA[20-150/0.5]-LB[20-70/0.5]

Hardness

Surface Treatment

Shaft Dia. D

(mm)

Shaft Tolerance

(mm)

RoHS?

Minsta beställningsantal

No Hardened	[Surface Treatment Provided] Black Oxide	10	h6	50 ～ 300	4 ～ 40	4 ～ 40	6 ～ 8	10	1 stycken
No Hardened	[Surface Treatment Provided] Black Oxide	12	h6	50 ～ 300	4 ～ 50	4 ～ 50	8 ～ 10	10	1 stycken
No Hardened	[Surface Treatment Provided] Black Oxide	15	h6	100 ～ 400	5 ～ 75	5 ～ 50	10 ～ 12	10	1 stycken
No Hardened	[Surface Treatment Provided] Black Oxide	20	h6	100 ～ 400	5 ～ 100	5 ～ 50	15 ～ 17	10	1 stycken
No Hardened	[Surface Treatment Provided] Black Oxide	25	h6	100 ～ 500	5 ～ 100	5 ～ 60	17 ～ 20	10	1 stycken
No Hardened	[Surface Treatment Provided] Black Oxide	30	h6	100 ～ 500	10 ～ 125	10 ～ 60	20 ～ 25	10	1 stycken
No Hardened	[Surface Treatment Provided] Black Oxide	35	h6	100 ～ 500	10 ～ 150	10 ～ 70	25 ～ 30	10	1 stycken
No Hardened	[Surface Treatment Provided] Black Oxide	40	h6	200 ～ 500	15 ～ 150	15 ～ 70	30 ～ 35	10	1 stycken
No Hardened	[Surface Treatment Provided] Black Oxide	50	h6	200 ～ 500	20 ～ 150	20 ～ 70	40 ～ 45	10	1 stycken
No Hardened	[Surface Treatment Provided] Black Oxide	10	h7	50 ～ 300	4 ～ 40	4 ～ 40	6 ～ 8	10	1 stycken
No Hardened	[Surface Treatment Provided] Black Oxide	12	h7	50 ～ 300	4 ～ 50	4 ～ 50	8 ～ 10	10	1 stycken
No Hardened	[Surface Treatment Provided] Black Oxide	15	h7	100 ～ 400	5 ～ 75	5 ～ 50	10 ～ 12	10	1 stycken
No Hardened	[Surface Treatment Provided] Black Oxide	20	h7	100 ～ 400	5 ～ 100	5 ～ 50	15 ～ 17	10	1 stycken
No Hardened	[Surface Treatment Provided] Black Oxide	25	h7	100 ～ 500	5 ～ 100	5 ～ 60	17 ～ 20	10	1 stycken
No Hardened	[Surface Treatment Provided] Black Oxide	30	h7	100 ～ 500	10 ～ 125	10 ～ 60	20 ～ 25	10	1 stycken
-	No Surface Treatment	10	h6	50 ～ 300	4 ～ 40	4 ～ 40	6 ～ 8	10	1 stycken
-	No Surface Treatment	12	h6	50 ～ 300	4 ～ 50	4 ～ 50	8 ～ 10	10	1 stycken
-	No Surface Treatment	15	h6	100 ～ 400	5 ～ 75	5 ～ 50	10 ～ 12	10	1 stycken
-	No Surface Treatment	20	h6	100 ～ 400	5 ～ 100	5 ～ 50	15 ～ 17	10	1 stycken
-	No Surface Treatment	25	h6	100 ～ 500	5 ～ 100	5 ～ 60	17 ～ 20	10	1 stycken
-	No Surface Treatment	30	h6	100 ～ 500	10 ～ 125	10 ～ 60	20 ～ 25	10	1 stycken
-	No Surface Treatment	35	h6	100 ～ 500	10 ～ 150	10 ～ 70	25 ～ 30	10	1 stycken
-	No Surface Treatment	40	h6	200 ～ 500	15 ～ 150	15 ～ 70	30 ～ 35	10	1 stycken
-	No Surface Treatment	50	h6	200 ～ 500	20 ～ 150	20 ～ 70	40 ～ 45	10	1 stycken
No Hardened	No Surface Treatment	10	h6	50 ～ 300	4 ～ 40	4 ～ 40	6 ～ 8	10	1 stycken
No Hardened	No Surface Treatment	12	h6	50 ～ 300	4 ～ 50	4 ～ 50	8 ～ 10	10	1 stycken
No Hardened	No Surface Treatment	15	h6	100 ～ 400	5 ～ 75	5 ～ 50	10 ～ 12	10	1 stycken
No Hardened	No Surface Treatment	20	h6	100 ～ 400	5 ～ 100	5 ～ 50	15 ～ 17	10	1 stycken
No Hardened	No Surface Treatment	25	h6	100 ～ 500	5 ～ 100	5 ～ 60	17 ～ 20	10	1 stycken
No Hardened	No Surface Treatment	30	h6	100 ～ 500	10 ～ 125	10 ～ 60	20 ～ 25	10	1 stycken
No Hardened	No Surface Treatment	35	h6	100 ～ 500	10 ～ 150	10 ～ 70	25 ～ 30	10	1 stycken
No Hardened	No Surface Treatment	40	h6	200 ～ 500	15 ～ 150	15 ～ 70	30 ～ 35	10	1 stycken
No Hardened	No Surface Treatment	50	h6	200 ～ 500	20 ～ 150	20 ～ 70	40 ～ 45	10	1 stycken
No Hardened	[Surface Treatment Provided] Electroless Nickel Plating	10	h6	50 ～ 300	4 ～ 40	4 ～ 40	6 ～ 8	10	1 stycken
No Hardened	[Surface Treatment Provided] Electroless Nickel Plating	12	h6	50 ～ 300	4 ～ 50	4 ～ 50	8 ～ 10	10	1 stycken
No Hardened	[Surface Treatment Provided] Electroless Nickel Plating	15	h6	100 ～ 400	5 ～ 75	5 ～ 50	10 ～ 12	10	1 stycken
No Hardened	[Surface Treatment Provided] Electroless Nickel Plating	20	h6	100 ～ 400	5 ～ 100	5 ～ 50	15 ～ 17	10	1 stycken
No Hardened	[Surface Treatment Provided] Electroless Nickel Plating	25	h6	100 ～ 500	5 ～ 100	5 ～ 60	17 ～ 20	10	1 stycken
No Hardened	[Surface Treatment Provided] Electroless Nickel Plating	30	h6	100 ～ 500	10 ～ 125	10 ～ 60	20 ～ 25	10	1 stycken
No Hardened	[Surface Treatment Provided] Electroless Nickel Plating	35	h6	100 ～ 500	10 ～ 150	10 ～ 70	25 ～ 30	10	1 stycken
No Hardened	[Surface Treatment Provided] Electroless Nickel Plating	40	h6	200 ～ 500	15 ～ 150	15 ～ 70	30 ～ 35	10	1 stycken
No Hardened	[Surface Treatment Provided] Electroless Nickel Plating	50	h6	200 ～ 500	20 ～ 150	20 ～ 70	40 ～ 45	10	1 stycken

Enhetspris (exklusive MOMS)(Enhetspris inklusive MOMS)	Standardavsändningsdatum

- ( - )	17 arbetsdagar
- ( - )	17 arbetsdagar
- ( - )	17 arbetsdagar
- ( - )	17 arbetsdagar
- ( - )	17 arbetsdagar
- ( - )	17 arbetsdagar
- ( - )	17 arbetsdagar
- ( - )	17 arbetsdagar
- ( - )	17 arbetsdagar
- ( - )	9 arbetsdagar
- ( - )	9 arbetsdagar
- ( - )	9 arbetsdagar
- ( - )	9 arbetsdagar
- ( - )	9 arbetsdagar
- ( - )	9 arbetsdagar
- ( - )	29 arbetsdagar
- ( - )	29 arbetsdagar
- ( - )	29 arbetsdagar
- ( - )	29 arbetsdagar
- ( - )	29 arbetsdagar
- ( - )	29 arbetsdagar
- ( - )	29 arbetsdagar
- ( - )	29 arbetsdagar
- ( - )	29 arbetsdagar
- ( - )	17 arbetsdagar
- ( - )	17 arbetsdagar
- ( - )	17 arbetsdagar
- ( - )	17 arbetsdagar
- ( - )	17 arbetsdagar
- ( - )	17 arbetsdagar
- ( - )	17 arbetsdagar
- ( - )	17 arbetsdagar
- ( - )	17 arbetsdagar
- ( - )	19 arbetsdagar
- ( - )	19 arbetsdagar
- ( - )	19 arbetsdagar
- ( - )	19 arbetsdagar
- ( - )	19 arbetsdagar
- ( - )	19 arbetsdagar
- ( - )	19 arbetsdagar
- ( - )	19 arbetsdagar
- ( - )	19 arbetsdagar

Grundläggande information

Teknisk information

Skiss och specifikationer

Specifications/Overview

■Selection of Driving Shaft
In selecting a driving shaft, select the basic shape and size from the specification table, then select necessary alterations such as thread machining, keyway addition etc.

[Selection Example of Part Number]
·Alteration Selection: A retaining ring groove, two set screw flats at 0° and 90° and a tap

Driving Shaft - Both Ends Stepped: Related Image

[App. Example]

Driving Shaft - Both Ends Stepped: Related Image

Katalog

Products homepage

Katalog (2-sidigt uppslag)