Artikelnummer:
kandidater hittades.Artikelnummer |
---|
Enhetspris (exklusive MOMS)(Enhetspris inklusive MOMS) | Standardavsändningsdatum |
---|
39.19 € ( 46.64 € ) | 5 arbetsdagar |
43.74 € ( 52.05 € ) | 5 arbetsdagar |
48.22 € ( 57.38 € ) | 5 arbetsdagar |
51.90 € ( 61.76 € ) | 5 arbetsdagar |
64.04 € ( 76.21 € ) | 5 arbetsdagar |
72.65 € ( 86.45 € ) | 5 arbetsdagar |
83.40 € ( 99.25 € ) | 5 arbetsdagar |
94.57 € ( 112.54 € ) | 5 arbetsdagar |
131.83 € ( 156.88 € ) | 5 arbetsdagar |
102.45 € ( 121.92 € ) | 5 arbetsdagar |
38.96 € ( 46.36 € ) | 5 arbetsdagar |
52.68 € ( 62.69 € ) | 5 arbetsdagar |
51.68 € ( 61.50 € ) | 5 arbetsdagar |
52.10 € ( 62.00 € ) | 5 arbetsdagar |
56.00 € ( 66.64 € ) | 5 arbetsdagar |
77.16 € ( 91.82 € ) | 5 arbetsdagar |
69.37 € ( 82.55 € ) | 5 arbetsdagar |
91.34 € ( 108.69 € ) | 5 arbetsdagar |
130.79 € ( 155.64 € ) | 5 arbetsdagar |
102.45 € ( 121.92 € ) | 5 arbetsdagar |
[Features]
-Demonstrates high performance in machining general steel, EN 1.4301 Equiv. (sintered) and heat-treated steel (up to 50 HRC)
-2-flute end mill for machining keyways
-The shape of the end cutting edge is almost flat so that the workpiece can be machined flat.
-Short cutting edge length that is resistant to chattering (1. 5 times longer than the cutting edge diameter)
-Since the cutting edge has been machined into a sharp corner, corner edges can also be machined
-Optimal for low to medium speed machining due to the universal 30° helix angle
-The coating has high oxidation resistance and high hardness and achieves long life. Effective in high-speed machining and dry machining as coating characteristics.
Model Number | Flute Length ℓ |
Overall Length L |
Shank Diameter d |
Figure | |
Outer Diameter D |
|||||
TSC-KPEM2S (+ Tolerance) TSC-KMEM2S (- Tolerance) |
2 | 3 | 45 | 6 | 1 |
3 | 5 | 45 | 6 | 1 | |
4 | 7 | 45 | 6 | 1 | |
5 | 8 | 50 | 6 | 1 | |
6 | 8 | 50 | 6 | 2 | |
7 | 10 | 60 | 8 | 1 | |
8 | 11 | 60 | 8 | 2 | |
10 | 13 | 70 | 10 | 2 | |
12 | 16 | 75 | 12 | 2 | |
14 | 21 | 75 | 16 | 1 |
For Cutting Conditions, Refer to >>Click here.
● It has a TS film coating with much greater oxidation resistance and hardness than conventional films, resulting in a longer operational life and ideal for high speed machining / dry machining.
● A 2-flute end-mill especially for key grooving.
● Has a nearly flat bottom blade shape that allows for a flat finish on the workpiece.
● Has a short blade length that is strong against chatter (length 1.5 times greater than blade diameter).
● The blade tip has a sharp edge allowing corner edges to also be machined.