Hybrid deep groove ball bearings / single row / ZZ / for special environmental conditions / grease-free, oil-free / MISUMI

Hybrid deep groove ball bearings / single row / ZZ / for special environmental conditions / grease-free, oil-free / MISUMI
  • Volume Discount
  • Order quantities extended (D-JIT)

Data sheet

Unit еxample related to this product

Part Number

Once your search is narrowed to one product,
the corresponding part number is displayed here.

Back to the Category Ball Bearings

Technical Drawing - Ball Bearings

 

EN 1.4301 Equiv. Non-Grease/Non-Oil Ball Bearings for Special Environments:Related Image

Available dimensions and tolerances can be found under the tab More information.

 

Basic Properties (e.g., material, hardness, coating, tolerance) - Ball Bearings

 

TypeInner and Outer RingShieldRolling ElementRetainer
MaterialHardnessMaterialMaterialMaterial
SE ZZPREN 1.4125 Equiv.
(Special Fluoro-Macromolecule Coating)
60HRCEN 1.4301 Equiv.EN 1.4125 Equiv.
(Special Fluoro-Macromolecule Coating)
EN 1.4301 Equiv.
(Special Fluoro-Macromolecule Coating)
3NC ZZSTEN 1.4125 Equiv.Ceramics
(Silicon Nitride)
Fluororesin
3NC ZZMDEN 1.4542 Equiv.40HRC

For details on the tolerance and allowable values of inner and outer rings, >> P.2243
For further specifications please see the More information tab.
Information on tolerances and rotational accuracy of the radial bearings can be found in the following PDF: Ball bearing table / tolerances as PDF

 

Composition of a Product Code  - Ball Bearings

 

Part Number
SUB6000ZZ
3NC6000ZZST
 
General Information - Ball Bearings

 

Ball bearing - deep groove ball bearing - axial bearing - axial ball bearing - axial groove ball bearing - angular ball bearing - spherical ball bearing - tension bearing

 

Ball Bearing Selection Details

- Ball material: steel, stainless steel, ceramic, plastic, glass, chrome-plated

- Type of bearings: axial ball bearings, thin section bearings, spherical ball bearings, deep groove ball bearings, single-row angular ball bearings, double-row ball bearings, tension bearings, four-point bearings

- Outer ring: flat, spherical, with flange, annular groove, U-groove, V-groove

- Properties: heat-resistant, non-magnetic, corrosion-resistant, dust-proof, vacuum, high speed

- Inner diameter: 2 mm to 50 mm

- Outer diameter: 5 mm to 110 mm
 

Ball bearing designation (suffix):

In addition to the dimensional designation of the ball bearing, ball bearings often also have a designation for a cover disc or sealing disc. The following names are the most common names of various manufacturers that can be selected in the MISUMI online shop.
 

- Double-sided sealing washer: 2RSH/2RS1, 2RSR/C-2HRS, DDU/DD
- Single-sided sealing washer: RSH/RS1, RSR/C-HRS, DU
- Double-sided sealing washer with low friction: 2RSL/2RZ/VV
- Double-sided cover disc: 2Z/ZZ, 2ZR/C-2Z
- Single sided cover disc: Z, ZR/C-Z/Z
 

Description/Basics

 

Rolling bearings

Rolling bearings are generally divided into ball bearings and roller bearings. Ball bearings are a popular type of rolling bearings due to their high permissible speed and low friction.
In the MISUMI online shop, you can purchase ball bearings that can be customized to your applications and environmental conditions. Our ball bearings are available in different materials and in a combination of different materials (hybrid bearings). In addition, MISUMI offers ball bearings already integrated into the housing as bearing housing.

 

Grooved ball bearings

Grooved ball bearings are the most commonly used rotary rolling bearings. This type of ball bearing is ideally suited for supporting rotating machine elements. A grooved ball bearings are intended for load bearing of radial forces and light axial forces. Grooved ball bearings are designed for high speeds and are used in a wide variety of industrial applications and designs. MISUMI already offers ball bearings integrated into housings and holders as bearing housings.

 

Areas of Application


Ball bearing - chemical resistance

Chemical resistance

Plastic ball

Metal ball

Ceramic ball

Bearing rings

UHMW

PEEK

PTFE

EN 1.4125 equivalent

EN 1.4301 equivalent

EN 1.4125 equivalent

EN 1.4542 equivalent

Cover plate

-

-

-

EN 1.4301 equivalent

EN 1.4301 equivalent

EN 1.4301 equivalent

EN 1.4301 equivalent

Bearing balls

Glass

Ceramic
(aluminum oxide)

Ceramic
(aluminum oxide)

EN 1.4125 equivalent

EN 1.4301 equivalent

Ceramic

Ceramic

Ball cage

UHMW

PEEK

PTFE

EN 1.4301 equivalent

EN 1.4301 equivalent

Fluoroplastic

Fluoroplastic

Acids

Hydrochloric acid

suitable to a limited extent

good

very good

unsuitable

good

suitable to a limited extent

good

Sulfuric acid

suitable to a limited extent

good

very good

unsuitable

very good

good

very good

Nitric acid

suitable to a limited extent

good

very good

unsuitable

very good

good

very good

Bases

unsuitable

very good

very good

unsuitable

very good

good

very good

Solvents

very good

very good

very good

unsuitable

very good

good

very good

Salt water

very good

very good

very good

unsuitable

very good

good

very good

Water

very good

very good

very good

unsuitable

very good

very good

very good

Comparison Table The ball bearing comparison table is provided for comparison purposes only (consider the lubricant and the sealing washer separately).
 

Ball bearing materials

In the MISUMI online shop, ball bearings are available in cost-effective rolling bearing steel, corrosion-resistant stainless steel and stainless steel. Furthermore, our product range includes various hybrid bearings in the following combinations: metal & ceramic, plastic & ceramic, plastic & glass.

Our various materials offer good resistance to various environmental influences. Our ball bearing shop includes the ball materials stainless steel, steel, UHMW, PEEK, PTFE, ceramic and glass.

 

Instructions for Use / Installation Information - Ball Bearings

 

Installation Information

An incorrect assembly and disassembly can damage a ball bearing. Therefore, a suitable tool must always be used to assemble and disassemble ball bearings or roller bearings.
Ball bearings should not be assembled with a hammer, as this can deform the ball bearing. It is recommended using a suitable press. During pressing, the contact surface can be provided with lubricant to protect the surfaces and facilitate assembly.
It is best to use a bearing puller for disassembly.

 

Maintenance

The ball bearing in roller bearings should be inspected for damage during maintenance.
Before regreasing, a ball bearing should first be thoroughly cleaned.
Remaining contamination in the bearing can damage the ball bearing. As a rule, a ball bearing should not be completely filled with grease, as this can cause the bearing to heat up too much and can cause it to fail.
For encapsulated and sealed ball bearings, it is recommended to replace the bearing. Maintenance is not recommended due to the risk of damage to the cover place or seal.
 

Supplementary Article

 

Bearing Lock Nuts

Shaft nuts - lock nuts - steel shaft nut - stainless steel shaft nut - shaft with retaining nut - shaftnNut with clamp screw - shaft nut with grub screw - shaft assembly

 

Bearings with Housing

Bearing with housing - bearing housing - bearing units - ball bearing holder - ball bearing with housing - bearing housing with flange - shaft holder with ball bearing

 

Axles / Rotary Shafts

Rotary axis - offset rotary shaft - double offset shaft - female threaded shaft - keyway shaft

 

Drive shafts

Motor shaft - torsion shaft - shaft with collar - shaft with shoulder - offset shaft - keyway shaft

 

Plain Bearing (Bushes)

Plain bearing - maintenance free - plain bearing bushings - plain bearing bushing with collar - plain bearing bushing with flange - plastic bushing - plastic plain bearing bushing

 

Industrial Applications

 

3D printer industry
Automotive industry
Pharmaceutical industry
Packaging industry

 

Part Number:  

    3D preview is not available, because the part number has not yet been determined.

  • In order to open the 3D preview, the part number must be fixed.
Loading...
Part Number
3NC6000ZZMD
3NC6000ZZST
3NC6001ZZMD
3NC6001ZZST
3NC6002ZZMD
3NC6002ZZST
3NC6004ZZST
Part Number
Standard Unit Price
Minimum order quantityVolume Discount
Standard
Shipping Days
?
RoHSMaterials of Inner and Outer Ring I.D. d
(φ)
O.D. D
(φ)
Width B (or T)
(mm)
Allowable Rotational Speed
(1/min)
Specifications/Environment Rolling Element Material

244.57 €

1 Available 5 Days 10[Stainless Steel] EN 1.4542 Equiv.102681000Standard / Heat Resistance / Water Resistance / Highly Corrosion Resistant Type / Vaccum Type[Ceramic] Ceramic (Silicon Nitride)

204.65 €

1 Available 5 Days 10[Stainless Steel] EN 1.4125 Equiv.102681000Standard / Heat Resistance / Water Resistance / Highly Corrosion Resistant Type / Vaccum Type[Ceramic] Ceramic (Silicon Nitride)

251.51 €

1 Available 5 Days 10[Stainless Steel] EN 1.4542 Equiv.12288830Standard / Heat Resistance / Water Resistance / Highly Corrosion Resistant Type / Vaccum Type[Ceramic] Ceramic (Silicon Nitride)

211.57 €

1 Available 5 Days 10[Stainless Steel] EN 1.4125 Equiv.12288830Standard / Heat Resistance / Water Resistance / Highly Corrosion Resistant Type / Vaccum Type[Ceramic] Ceramic (Silicon Nitride)

267.87 €

1 Available 5 Days 10[Stainless Steel] EN 1.4542 Equiv.15329660Standard / Heat Resistance / Water Resistance / Highly Corrosion Resistant Type / Vaccum Type[Ceramic] Ceramic (Silicon Nitride)

224.81 €

1 Available 5 Days 10[Stainless Steel] EN 1.4125 Equiv.15329660Standard / Heat Resistance / Water Resistance / Highly Corrosion Resistant Type / Vaccum Type[Ceramic] Ceramic (Silicon Nitride)

256.15 €

1 Available 5 Days 10[Stainless Steel] EN 1.4125 Equiv.204212500Standard / Heat Resistance / Water Resistance / Highly Corrosion Resistant Type / Vaccum Type[Ceramic] Ceramic (Silicon Nitride)

Loading...

  1. 1

Back to the Category Ball Bearings

Technical Drawing - Ball Bearings

EN 1.4301 Equiv. Non-Grease/Non-Oil Ball Bearings for Special Environments:Related Image

 

Specification Tables - Ball Bearings
 
Part NumberdDBr
(min)
Allowable Radial Load NAllowable Rotational Speed
rpm (Reference)
Relative DimensionsMass (g)Unit Price
Dsdh
(max)
R
(max)
Clean TypeVacuumHighly Corrosion ResistantSE6 Type3NC Type(min)(max)SE□ZZPR3NC□ZZST3NC□ZZMDSEZZPR3NCZZST3NCZZMD
SE624ZZPR--41350.240-10005.66.911.40.22.93-- --
SE626ZZPR--61960.380-810.6170.37.90-- --
SE608ZZPR--82270.3100-1012.42011.81-- --
SE6000ZZPR3NC6000ZZST3NC6000ZZMD102680.313535121324191617   
SE6200ZZPR--3090.6155508601415260.632-- --
SE6001ZZPR3NC6001ZZST3NC6001ZZMD122880.3155408300.3201718   
SE6201ZZPR--32100.6205707701616.5280.636-- --
SE6002ZZPR3NC6002ZZST3NC6002ZZMD153290.3170456601718.5300.3302627   
SE6202ZZPR--35110.6230756101919.5310.64438- --
SE6004ZZPR3NC6004ZZST-204212280705002425380.36356-  -
SE6204ZZPR--47141.03851304502526.5420.610592- --
Priority is given to the life of solid lubricant (Fluororesin Retainer). Use within the allowable load range.
Allowable rotational speed is based on 1/2 of allowable load.
kgf=Nx0.101972

More Information

Performance Comparison of Bearings for Special Environment
Part NumberInner/Outer RingsShieldRolling ElementRetainerLow Dust GenerationAbrasion ResistanceCorrosion Resistance and Chemical ResistanceHeat ResistanceVacuumInsulationNon-magneticHeavy LoadHigh Rotational Speed
AcidAlkaliSolventSeawaterWater
Hydrochloric AcidSulfuric AcidNitric Acid
SE6□□□ZZPREN 1.4125 Equiv.
Special Fluoro-Macromolecule Coating
EN 1.4301 Equiv.EN 1.4125 Equiv.
Special Fluoro-Macromolecule Coating
EN 1.4301 Equiv.
Special Fluoro-Macromolecule Coating
××××××××
(-100~200°C)
×××
3NC6□□□ZZSTEN 1.4125 Equiv.EN 1.4301 Equiv.CeramicsFluororesin×
(-100~200°C)
×××
3NC6□□□ZZMDEN 1.4542 Equiv.EN 1.4301 Equiv.CeramicsFluororesin×
(-100~200°C)
××
SUB6□□□ZZEN 1.4301 Equiv.EN 1.4301 Equiv.EN 1.4301 Equiv.EN 1.4301 Equiv.×
(-40~150°C)
××××
The service life may be shortened drastically when used in conditions where the product is soaked in corrosive solution.
(◎Well Suited ○Good △Questionable ×Not Suitable)

Basic information

Bearing Ring Shape Ball Shield material and shape Double Shielded Outer Ring Type Flat
Accuracy  (JIS) Class 0 Load Direction Radial Number of Bearing Ring Rows Single Track
Size Standard Metric Series Seal Part Structure Double Shielded

Complementary Products

MISUMI Unit еxample related to this product

Tech Support

Technical Support
Tel:+49 69 668173-0 / FAX:+49 69 668173-360