Angle brackets / unmachined, through hole, parallel pin bore / aluminium, cast iron / treatment selectable

Click on this image to zoom in.

View the FAQ (4)

MISUMI

Part Number

Once your search is narrowed to one product,
the corresponding part number is displayed here.

Drawing / Specifications
3D Preview 3D preview is available after complete configuration
Part Numbers
More Information
Catalog

Dimensional Drawing

■Hole Machining Selection FB (No Hole)
Angle Plates - Side A (Base Surface) Machining Configurable: Related Image

■Dimensional Tolerances Without Command

Dimension Range		Tolerance (㎜)
Over	or less	Tolerance (㎜)
0.5	6	±0.1
6	30	±0.2
30	120	±0.3
120	400	±0.5

[ ! ]Compliant with JIS B 0405 Class m (intermediate).

■Hole Machining Selection D (Through Holes)

When A = 75 or less When A = 80 or more Angle Plates - Side A (Base Surface) Machining Configurable: Related Image

■Hole Machining Selection K (Through Holes and Dowel Holes)

When A = 50 When A = 65 to 75 When A = 80 or more Angle Plates - Side A (Base Surface) Machining Configurable: Related Image

Type	Hole Machining Selection	[M] Material	[S] Surface Treatment
IKC	FB (No Hole) D (Through Holes) K (Through Holes and Dowel Holes)	EN−JL 1040 Equiv.	Primer Coating (Gray)
BIKC			Black Oxide
MIKC			Electroless Nickel Plating
AIKC		EN AC−51300 Equiv.	—

[ ! ] EN−JL 1040 Equiv.: Surface treatment is not applied to machined surfaces and holes.
[!] A dimension is ground from the gusset side. Please note that, as shown in the photo, no surface treatment is applied on the gusset side.
[ NG ] BIKCK is not selectable.
[ ! ] Regarding the Black Oxide on EN−JL 1040 Equiv., there is a possibility that the casting surface will turn reddish-brown.

Specification Table

Part Number	—	A	—	W
IKCFB100 MIKCK150	— —	A85 A65	— —	W75 W100

Part Number		Angle Plate Body
Type	H	A 5 mm Increments	W Selection	T	T₁
IKCFB BIKCFB MIKCFB AIKCFB	100	50	75 80 100	15	14
		80 to 100
	150	65 to 75	60 75 100	15	14
		80 to 100	75 80 100
	200	65 to 75	60 75	15	14
		85 to 120	75 80 100
	250	85 to 120	75 80 100	18	15
	300	90 to 150		18	15
	350	90 to 150
	400	90 to 150

[ NG ] For AIKCFB, W60 is not available

Part Number		Angle Plate Body				Through Hole
Type	H	A 5 mm Increments	W Selection	T	T₁	d		B			X	F	Y	G
						W = 60	W = 75·80·100	W = 60	W = 75·80	W = 100
IKCD BIKCD MIKCD AIKCD	100	50	75 80 100	15	14	—	11	—	50	70	35	—	45	40
		80 to 100										A−50
	150	65 to 75	60 75 100	15	14	9	11	40	50	70	35	—	75	60
		80 to 100	75 80 100			—		—				A−50
	200	65 to 75	60 75	15	14	9	11	40	50	—	35	—	110	70
		85 to 120	75 80 100			—		—		70	40	A−50
	250	85 to 120	75 80 100	18	15	—	11	—	50	70	40	A−55	140	90
	300	90 to 150		18	15		11		50	70	40	A−60	190	90
	350	90 to 150											230	100
	400	90 to 150											260	120

[ NG ] For AIKCD, W60 is not available
[ ! ] Portions without specific dimensions are same as FB (No Hole Type)

Part Number		Angle Plate Body				Through Hole									Dowel Hole
Type	H	A 5 mm Increments	W Selection	T	T₁	d		B			X	F	Y	G	D_H7		a	h
						W = 60	W = 75·80·100	W = 60	W = 75·80	W = 100					W = 60	W = 75·80·100
IKCK MIKCK AIKCK	100	50	75 80 100	15	14	—	11	—	50	70	35	—	45	40	—	10	—	65
		80 to 100										A−50					X+ (F/2)
	150	65 to 75	60 75 100	15	14	9	11	40	50	70	35	—	75	60	6	10	A−15	105
		80 to 100	75 80 100			—		—				A−50			—		X+ (F/2)
	200	65 to 75	60 75	15	14	9	11	40	50	—	35	—	110	70	6	10	A−15	145
		85 to 120	75 80 100			—		—		70	40	A−50			—		X+ (F/2)
	250	85 to 120	75 80 100	18	15	—	11	—	50	70	40	A−55	140	90	—	10	X+ (F/2)	185
	300	90 to 150		18	15		11		50	70	40	A−60	190	90				235
	350	90 to 150											230	100				280
	400	90 to 150											260	120				320

[ NG ] For AIKCK, W60 is not available
[ ! ] Portions without specific dimensions are same as FB (No Hole Type)
[ NG ] BIKCK is not selectable.

Alterations

Alteration

Code

Spec.

Side H Tapped Hole Change

Changes the holes 4 × d (through holes) on side H to tapped holes.

d	MC
9	M8
11	M10

Ordering Code MC

Part Number:

3D preview is not available, because the part number has not yet been determined.

In order to open the 3D preview, the part number must be fixed.

Plug-in is required for 3D Preview

CAD Download

Data to be displayed: 30; 45; 60

Part Number
BIKCD100-A[50,80,85,90,95,100]-W[75,80,100]
BIKCD150-A[65-100/5]-W[60,75,80,100]
BIKCD200-A[65-75/5]-W[60,75,80,100]
BIKCD200-A[85-120/5]-W[60,75,80,100]
BIKCD250-A[85-120/5]-W[75,80,100]
BIKCD300-A[90-150/5]-W[75,80,100]
BIKCD350-A[90-150/5]-W[75,80,100]
BIKCD400-A[90-150/5]-W[75,80,100]
BIKCFB100-A[50,80,85,90,95,100]-W[75,80,100]
BIKCFB150-A[65-100/5]-W[60,75,80,100]
BIKCFB200-A[65-75/5]-W[60,75,80,100]
BIKCFB200-A[85-120/5]-W[60,75,80,100]
BIKCFB250-A[85-120/5]-W[75,80,100]
BIKCFB300-A[90-150/5]-W[75,80,100]
BIKCFB350-A[90-150/5]-W[75,80,100]
BIKCFB400-A[90-150/5]-W[75,80,100]

Minimum order quantity	Standard Shipping Days ?	RoHS	Material	Hole Machining	Surface Treatment	Height H (mm)	Dimension A (mm)	W (mm)
1	13 Days	10	Steel	Through Hole	Black Oxide	100	50 ～ 100	75 ～ 100
1	13 Days	10	Steel	Through Hole	Black Oxide	150	65 ～ 100	60 ～ 100
1	13 Days	10	Steel	Through Hole	Black Oxide	200	65 ～ 75	60 ～ 100
1	13 Days	10	Steel	Through Hole	Black Oxide	200	85 ～ 120	60 ～ 100
1	13 Days	10	Steel	Through Hole	Black Oxide	250	85 ～ 120	75 ～ 100
1	13 Days	10	Steel	Through Hole	Black Oxide	300	90 ～ 150	75 ～ 100
1	13 Days	10	Steel	Through Hole	Black Oxide	350	90 ～ 150	75 ～ 100
1	13 Days	10	Steel	Through Hole	Black Oxide	400	90 ～ 150	75 ～ 100
1	13 Days	10	Steel	No Hole	Black Oxide	100	50 ～ 100	75 ～ 100
1	13 Days	10	Steel	No Hole	Black Oxide	150	65 ～ 100	60 ～ 100
1	13 Days	10	Steel	No Hole	Black Oxide	200	65 ～ 75	60 ～ 100
1	13 Days	10	Steel	No Hole	Black Oxide	200	85 ～ 120	60 ～ 100
1	13 Days	10	Steel	No Hole	Black Oxide	250	85 ～ 120	75 ～ 100
1	13 Days	10	Steel	No Hole	Black Oxide	300	90 ～ 150	75 ～ 100
1	13 Days	10	Steel	No Hole	Black Oxide	350	90 ～ 150	75 ～ 100
1	13 Days	10	Steel	No Hole	Black Oxide	400	90 ～ 150	75 ～ 100

General Information - Angle Brackets

Angle console - angle console with through hole - angle bracket with reinforcement rib - angle bracket without hole - angle bracket wide - angle bracket with oblong hole - angle bracket welded

Angle Bracket Selection Details

- Material: aluminum, steel, cast steel, stainless steel
- Coatings: untreated, burnished, primed (grey), nickel-plated
- Design: cast, welded
- Perpendicularity: up to 0.02/100
- Bore holes: without bore hole, through-hole, internal thread, dowel pin bore, oblong hole
- Dowel pin bore: H7
- Length A: 40 to 150 mm
- Length H: 50 to 500 mm
- Width: 30 to 100 mm

Description/Basics

Basically, an angle bracket is used for precise and solid fastening or connecting of different components and as frame constructions in mechanical and plant engineering. In most cases, angle brackets are uneven.
Due to its high perpendicularity, an angle bracket is among the precise mounting angles. Thanks to their stiffening rib, the angle bracket is also more solid and stiffer than conventional mounting angles and offers a precise, robust and secure connection.
MISUMI offers angle brackets with configurable through holes and dowel pin bores. The through hole can be converted to a tapped hole using the [MC] option. In addition, with the help of the option [LN, HN], the through hole of the angle brackets can be changed to an elongated hole. The angle bracket itself or the element to be fastened can thus be adjusted. The optional dowel pin holes in conjunction with dowel pins offer the possibility of aligning and mounting components such as manual stages, cylinders or other devices as accurately as possible on an angle bracket.
Our angle brackets are also available as blanks without mounting holes for individual machining.
Due to the many variations of an angle bracket, it offers design flexibility. This allows adapting it to the machine environment. With MISUMI, you can configure and have your steel brackets customized or stainless steel angles customized.
Angle brackets are often used as cylinder holders for air cylinders, as the exact straightness and exact position of the dowel pin bores allow for exact positioning of the cylinders. An angle console is also suitable for holding and holding positioning stages. Occasionally, the angle bracket is also used in clamping technology to accommodate the push-pull toggle clamps, clamp cylinder or gripper.
MISUMI offers for assembly different threaded rods and nuts, as well as washers.

Steel angle bracket/steel bracket

The benefits an angle bracket made of steel (cast steel) provides are primarily its high strength and the load capacity of the base material. As a result, steel angle brackets can absorb high loads.
Since steel has good quality, it is less expensive to manufacture, easy to rework and welds well. Compared to many other metallic raw materials, steel is quite cost-effective and can therefore be found in many applications.
Thanks to its good thermal conductivity, a steel angle or steel angle bracket can be used in areas with high temperatures. Since steel tends to oxidize, a coating should be provided as much as possible depending on the angle bracket. For this purpose, you can choose between either burnished, nickel-plated or primed.

Stainless steel angle bracket/stainless steel bracket

Angle brackets made of steel or stainless steel are characterized by their high durability. Thanks to their resistance, stainless steel angle brackets are very robust and stable. They are less prone to corrosion because the chrome content forms a passive layer (oxide film). Especially in corrosive environments, it is possible to use an angle bracket made of stainless steel (stainless steel), since the base material is very high-quality. Stainless steel also has high temperature resistance and can be welded. However, at higher temperatures, or even when welding the material, discoloration can occur (tempering colour). The stainless steel angles are also hygienic due to the material and are often used in medical technology.

Aluminum angle bracket/aluminum bracket

An important advantage of aluminum angle brackets is their reduced weight compared to steel or stainless steel angle brackets. This special feature can contribute to weight reduction in many applications. With regard to the low weight, the aluminum angle brackets have by comparison a high strength and can withstand high loads.
In addition, the simple processing and post-processing of the material makes the aluminum angle consoles cost-efficient. Similar to stainless steel, aluminum forms an oxide film and is thus well protected against corrosion. Another advantage of the angle bracket made of aluminum is that the base material has a low thermal expansion. This allows these angle consoles to be used in applications that are subject to frequent temperature changes. Angle consoles made of aluminum also have good electrical conductivity and can thus dissipate electrical voltages such as electrical static charges. This is often necessary in electrical systems or in the electronics industry for the production of electronic components.

Application Examples - Angle Brackets

Application example: angle bracket - angle bracket with cylinder - angle bracket with guided cylinder - holder cylinder - cylinder holder

Application example: angle bracket with guide cylinder
(1) Angle bracket, (2) Hexagon socket screw, (3) Air cylinder, (4) Dowel pin

Application example: angle bracket - angle bracket with quick clamp - angle bracket with clamping function

Application example: angle bracket with push-pull toggle clamps
(1) Mounting plate, (2) push-pull toggle clamps, (3) angle bracket

Application example: angle bracket - angle bracket with cylinder - angle bracket with cylinder pin bore - cylinder holder - cylinder brackets

Application example: angle bracket with cylinder
(1) Angle bracket, (2) hinge bolts, (3) cylinder

Industrial Applications

3D printer industry

Automotive industry

Pharmaceutical industry

Packaging industry

Products homepage

Basic information

Strength	Standard (Cast)

Configure

16Suggestion of an applicable part number.

View Part Numbers

Some specification is not specified yet.

The part number is completed.

Basic Attributes

Material
- Steel
- Aluminum
Clear
Hole Machining
- Through Hole
- Through Holes and Dowel Holes
- No Hole
Clear
Height H(mm)
100

150

200

250

300

350

400
Clear
Dimension A(mm)
50

80

85

90

95

100
[65-150/5mm Unit(s)]
Clear
W(mm)
60

75

80

100
Clear
Type
- AIKCD
- AIKCFB
- AIKCK
- BIKCD
- BIKCFB
- IKCD
- IKCFB
- IKCK
- MIKCD
- MIKCFB
- MIKCK
Clear
Surface Treatment
- Electroless Nickel Plating
- Black Oxide
- Primer Paint (Gray)
- Not Provided
Clear
Filter by CAD data type
- 2D
- 3D
Clear

Filter by standard shipping days

All

13 Days or Less
Reset

Optional Attributes

The specifications and dimensions of some parts may not be fully covered. For exact details, refer to manufacturer catalogs .

Frequently Asked Questions (FAQ)

Question:
What do you use the angle brackets for?: Answer:
An angle bracket can be used for a wide variety of applications in mechanical engineering. In general, they are used to connect or fix different components and devices. Angle brackets are manufactured very precisely with their perpendicularity compared to conventional mounting angles. Therefore, angle brackets are also frequently used to accommodate pneumatic cylinders, positioning stages, and stages. Another benefit of the angle bracket is its high rigidity due to the additional stiffening rib. This provides the angle bracket with a very good stability. Therefore, it can absorb heavier loads compared to normal angles.
Question:
What are the different types of steel on angle brackets?: Answer:
MISUMI offers the massive and precise angle bracket in two different types of steel. The MISUMI product range offers the material EN 1.0038 equivalent, which is also known as S235JR. This material is often used for extruded profiles. This shows good ductility, toughness and plasticity. As a further material, the range contains the EN-JL 1040 equivalent. This is grey cast iron with slat graphite, which has very good workability and is often used in machine tools.
Question:
What coatings are available for angle brackets made of steel?: Answer:
Our angle brackets are available untreated for further processing. To protect against corrosion, the angle bracket can be burnished, primed (grey) and nickel-plated.
Question:
What are the advantages of aluminum brackets?: Answer:
Aluminum brackets and aluminum angle brackets have a low weight and are therefore suitable for weight reduction. Aluminum, on the other hand, has a high strength in relation to heavier materials. As a result, these are also suitable for high loads. Another advantage is that aluminum does not require further corrosion protection. In addition, aluminum has a low thermal expansion, which gives it dimensional stability in case of temperature fluctuations.

Show more FAQ Close

Complementary Products

Guide Rails
MISUMI Shipping Days: 10 Days
[Precision] X-Axis / Cross Roller
MISUMI Standard Price : 311.07 € Shipping Days: 7 Days
Socket Head Cap Screws / Configurable Length
MISUMI Shipping Days: 6 Days
5 Series / Sheet Metals
MISUMI Standard Price : 1.33 € Shipping Days: Same day