Filtreringsvillkor

Outer Diameter D(Ø)
- 3.18
- 4
- 6
- 6.35
- 8
- 9.53
- 10
- 12
O.D. [Distinction]
* ~2 represents over 5, and 3 or less.
Inner Diameter d(Ø)
- 2.5
- 4
- 6
- 7.5
- 9
I.D. [Distinction]
* ~2 represents over 5, and 3 or less.
Bundle winding length(m)
- 8
- 10
- 16
- 20
Applicable Tube Size
- Inch Size
- Metric Size
Maximum operating pressure(MPa)
- 0.9
- 1.4
- 1.6
Type
- TD
- TID
CAD
- 2D
Uppskattade leveransdagar
- Alla
- Inom 4 arbetsdagar
- Inom 22 arbetsdagar
- Inom 26 arbetsdagar
- Inom 66 arbetsdagar

Soft Fluoropolymer Tubing TD / TID Series

Katalog

Artikelnummer:

Ej färdigt: 20 kandidater hittades.

Produktinformation
Artikelnummerlista
Detaljerad information
Katalog

Produktinformation

Specifications of Soft Fluoropolymer Tubing TD Series

Size		Metric Size
Nominal		TD0425	TD0604	TD0806	TD1075	TD1209
Outer diameter (mm)		4	6	8	10	12
Inner diameter (mm)		2.5	4	6	7.5	9
Roll	10 m	●	●	●	●	●
Roll	20 m	●	●	●	●	●
Color		Translucent (material color)
Applicable Fluids		See the catalog for applicable fluids.
Fluid^{Note 1)}		Air, water^{Note 1)}, inert gas
Applicable fittings^{Note 1)}		Insert fittings KF Series Stainless steel 316 insert fittings KFG2 Series Miniature fittings M, MS Series (Hose-nipple type) Fluoropolymer fittings LQ Series
Maximum operating pressure (MPa)	20°C	1.6	1.4	0.9	0.9	0.9
	100°C	0.9	0.7	0.5	0.5	0.5
	200°C	0.45	0.35	0.25	0.25	0.25
	260°C	0.23	0.2	0.15	0.15	0.15
Minimum bending radius mm^{Note 3)}	Recommended radius	15	25	45	55	75
Minimum bending radius mm^{Note 3)}	Tube close bend radius	8	16	31	35	41
Maximum operating temperature (fixed usage)		260°C
Material		Modified PTFE (Polytetrafluoroethylene resin)

Note 1) When using a liquid fluid, the surge pressure must be under the maximum operating pressure. If the surge pressure exceeds the maximum operating pressure, it will result in damage to the fittings and tubing. Furthermore, abnormal temperature rise caused by adiabatic compression may result in the tubing bursting.
Note 2) Do not use this product in a manner in which the tubing is not fixed. Observe the lesser value of the maximum operating pressure between the tubing and fittings. A material change over a long duration or due to high temperature may cause leakage. Perform periodic maintenance and replace with a new product immediately when abnormalities are detected.
Note 3) The minimum bending radius is the representative value measured as shown in the figure on the left.

Use a tube above the recommended minimum bending radius.
The tubing may be bent if used under the recommended minimum bending radius. Therefore, refer to the tube close bend radius and make sure that the tubing is not bent or flattened.
The tube close bend radius is not guaranteed. The value of 2R is measured with a bent or flattened tube.

Fluoropolymer Tubing TD/TID Series: related images

How to measure the minimum bending radius

Bend the tubing into a U shape at a temperature of 20°C. Fix one end and close the loop gradually. Measure 2R when the deformed ratio of the tubing diameter at bending reaches 5%.

Maximum operating pressure

Specifications of Soft Fluoropolymer Tubing TID Series

Size		Inch Size
Nominal		TID01	TID05	TID07	TID11	TID13
Outer diameter	inch	1/8 "	3/16 "	1/4 "	3/8 "	1/2 "
Outer diameter	mm	3.18	4.75	6.35	9.53	12.7
Inner diameter	inch	0.086 "	0.124 " (1/8 ")	0.156 " (5/32 ")	0.25 " (1/4 ")	0.374 " (3/8 ")
Inner diameter	mm	2.18	3.15	3.95	6.33	9.5
Roll	8 m (25 ft)	●	●	●	●	●
Roll	16 m (50 ft)	●	●	●	●	●
Color		Translucent (material color)
Applicable Fluids		See the catalog for applicable fluids.
Fluid^{Note 1)}		Air, water^{Note 1)}, inert gas
Applicable fittings^{Note 2)}		Stainless steel 316 inert fittings KFG2 series Fluoropolymer Fittings LQ Series
Maximum operating pressure (MPa)	20°C	1.4	1.4	1.6	1.4	0.9
	100°C	0.7	0.7	0.9	0.7	0.5
	200°C	0.35	0.35	0.45	0.35	0.25
	260°C	0.2	0.2	0.23	0.2	0.15
Minimum bending radius mm^{Note 3)}	Recommended radius	15	20	25	40	75
Minimum bending radius mm^{Note 3)}	Tube close bend radius	9	10	15	23	42
Maximum operating temperature (fixed usage)		260°C
Material		Modified PTFE (Polytetrafluoroethylene resin)

Use a tube above the recommended minimum bending radius.
The tubing may be bent if used under the recommended minimum bending radius. Therefore, refer to the tube close bend radius and make sure that the tubing is not bent or flattened.
The tube close bend radius is not guaranteed. The value of 2R is measured with a bent or flattened tube.

How to measure the minimum bending radius

Bend the tubing into a U shape at a temperature of 20°C. Fix one end and close the loop gradually. Measure 2R when the deformed ratio of the tubing diameter at bending reaches 5%.

Maximum operating pressure

Artikelnummerlista

Antal artiklar

Artikelnummer

Outer Diameter D

(Ø)

O.D. [Distinction]

Inner Diameter d

(Ø)

I.D. [Distinction]

Minimum Bending Radius

(mm)

Bundle winding length

(m)

Applicable Tube Size

Maximum operating pressure

(MPa)

Minsta beställningsantal

4	Up to 4	2.5	Up to 3	15	10	Metric Size	1.6	1 stycken
4	Up to 4	2.5	Up to 3	15	20	Metric Size	1.6	1 stycken
6	Up to 6	4	Up to 4	25	10	Metric Size	1.4	1 stycken
6	Up to 6	4	Up to 4	25	20	Metric Size	1.4	1 stycken
8	Up to 8	6	Up to 6	45	10	Metric Size	0.9	1 stycken
8	Up to 8	6	Up to 6	45	20	Metric Size	0.9	1 stycken
10	Up to 10	7.5	Up to 8	55	10	Metric Size	0.9	1 stycken
10	Up to 10	7.5	Up to 8	55	20	Metric Size	0.9	1 stycken
12	Up to 15	9	Up to 9	-	10	Metric Size	0.9	1 stycken
12	Up to 15	9	Up to 9	-	20	Metric Size	0.9	1 stycken
3.18	Up to 4	-	Up to 3	15	8	Inch Size	1.4	1 stycken
3.18	Up to 4	-	Up to 3	15	16	Inch Size	1.4	1 stycken
-	Up to 5	-	Up to 4	20	8	Inch Size	1.4	1 stycken
-	Up to 5	-	Up to 4	20	16	Inch Size	1.4	1 stycken
6.35	Up to 7	-	Up to 4	25	8	Inch Size	1.6	1 stycken
6.35	Up to 7	-	Up to 4	25	16	Inch Size	1.6	1 stycken
9.53	Up to 10	-	Up to 7	40	8	Inch Size	1.4	1 stycken
9.53	Up to 10	-	Up to 7	40	16	Inch Size	1.4	1 stycken
-	Up to 15	-	Up to 10	-	8	Inch Size	0.9	1 stycken
-	Up to 15	-	Up to 10	-	16	Inch Size	0.9	1 stycken

Enhetspris (exklusive MOMS)(Enhetspris inklusive MOMS)	Standardavsändningsdatum

63.35 € ( 75.39 € )	4 arbetsdagar
126.66 € ( 150.73 € )	4 arbetsdagar
127.45 € ( 151.67 € )	4 arbetsdagar
254.89 € ( 303.32 € )	66 arbetsdagar
186.23 € ( 221.61 € )	22 arbetsdagar
372.39 € ( 443.14 € )	4 arbetsdagar
293.69 € ( 349.49 € )	22 arbetsdagar
587.40 € ( 699.01 € )	4 arbetsdagar
418.98 € ( 498.59 € )	4 arbetsdagar
837.94 € ( 997.15 € )	4 arbetsdagar
35.58 € ( 42.34 € )	4 arbetsdagar
71.16 € ( 84.68 € )	4 arbetsdagar
66.81 € ( 79.50 € )	4 arbetsdagar
133.68 € ( 159.08 € )	26 arbetsdagar
131.53 € ( 156.52 € )	4 arbetsdagar
262.98 € ( 312.95 € )	4 arbetsdagar
275.94 € ( 328.37 € )	4 arbetsdagar
551.81 € ( 656.65 € )	4 arbetsdagar
385.85 € ( 459.16 € )	4 arbetsdagar
771.69 € ( 918.31 € )	22 arbetsdagar

Detaljerad information

Grundläggande information

Grundläggande information

Compatible with Japan's Food Sanitation Law.
[Features]
・ Flexibility: About 20% improvement
・ Operating temperature is MAX.260°C
[Applications]
・ Ideal for use when flexibility is required

Försiktighet

The maximum operating pressure values listed are at 20°C or less. See the catalog for details.
The last digits of the product codes indicate the length of the tubings.

Katalog

Katalog (2-sidigt uppslag)