Soft Fluoropolymer Tubing TD / TID Series

Click on this image to zoom in.

Compatible with Japan's Food Sanitation Law.
[Features]
・ Flexibility: About 20% improvement
・ Operating temperature is MAX.260°C
[Applications]
・ Ideal for use when flexibility is required

(i)Remark

The maximum operating pressure values listed are at 20°C or less. See the catalog for details.
The last digits of the product codes indicate the length of the tubings.

Part Number

Once your search is narrowed to one product,
the corresponding part number is displayed here.

Product specification
Part Numbers
Catalog

Specifications of Soft Fluoropolymer Tubing TD Series

Size		Metric Size
Nominal		TD0425	TD0604	TD0806	TD1075	TD1209
Outer diameter (mm)		4	6	8	10	12
Inner diameter (mm)		2.5	4	6	7.5	9
Roll	10 m	●	●	●	●	●
Roll	20 m	●	●	●	●	●
Color		Translucent (material color)
Applicable Fluids		See the catalog for applicable fluids.
Fluid^{Note 1)}		Air, water^{Note 1)}, inert gas
Applicable fittings^{Note 1)}		Insert fittings KF Series Stainless steel 316 insert fittings KFG2 Series Miniature fittings M, MS Series (Hose-nipple type) Fluoropolymer fittings LQ Series
Maximum operating pressure (MPa)	20°C	1.6	1.4	0.9	0.9	0.9
	100°C	0.9	0.7	0.5	0.5	0.5
	200°C	0.45	0.35	0.25	0.25	0.25
	260°C	0.23	0.2	0.15	0.15	0.15
Minimum bending radius mm^{Note 3)}	Recommended radius	15	25	45	55	75
Minimum bending radius mm^{Note 3)}	Tube close bend radius	8	16	31	35	41
Maximum operating temperature (fixed usage)		260°C
Material		Modified PTFE (Polytetrafluoroethylene resin)

Note 1) When using a liquid fluid, the surge pressure must be under the maximum operating pressure. If the surge pressure exceeds the maximum operating pressure, it will result in damage to the fittings and tubing. Furthermore, abnormal temperature rise caused by adiabatic compression may result in the tubing bursting.
Note 2) Do not use this product in a manner in which the tubing is not fixed. Observe the lesser value of the maximum operating pressure between the tubing and fittings. A material change over a long duration or due to high temperature may cause leakage. Perform periodic maintenance and replace with a new product immediately when abnormalities are detected.
Note 3) The minimum bending radius is the representative value measured as shown in the figure on the left.

Use a tube above the recommended minimum bending radius.
The tubing may be bent if used under the recommended minimum bending radius. Therefore, refer to the tube close bend radius and make sure that the tubing is not bent or flattened.
The tube close bend radius is not guaranteed. The value of 2R is measured with a bent or flattened tube.

Fluoropolymer Tubing TD/TID Series: related images

How to measure the minimum bending radius

Bend the tubing into a U shape at a temperature of 20°C. Fix one end and close the loop gradually. Measure 2R when the deformed ratio of the tubing diameter at bending reaches 5%.

Maximum operating pressure

Specifications of Soft Fluoropolymer Tubing TID Series

Size		Inch Size
Nominal		TID01	TID05	TID07	TID11	TID13
Outer diameter	inch	1/8 "	3/16 "	1/4 "	3/8 "	1/2 "
Outer diameter	mm	3.18	4.75	6.35	9.53	12.7
Inner diameter	inch	0.086 "	0.124 " (1/8 ")	0.156 " (5/32 ")	0.25 " (1/4 ")	0.374 " (3/8 ")
Inner diameter	mm	2.18	3.15	3.95	6.33	9.5
Roll	8 m (25 ft)	●	●	●	●	●
Roll	16 m (50 ft)	●	●	●	●	●
Color		Translucent (material color)
Applicable Fluids		See the catalog for applicable fluids.
Fluid^{Note 1)}		Air, water^{Note 1)}, inert gas
Applicable fittings^{Note 2)}		Stainless steel 316 inert fittings KFG2 series Fluoropolymer Fittings LQ Series
Maximum operating pressure (MPa)	20°C	1.4	1.4	1.6	1.4	0.9
	100°C	0.7	0.7	0.9	0.7	0.5
	200°C	0.35	0.35	0.45	0.35	0.25
	260°C	0.2	0.2	0.23	0.2	0.15
Minimum bending radius mm^{Note 3)}	Recommended radius	15	20	25	40	75
Minimum bending radius mm^{Note 3)}	Tube close bend radius	9	10	15	23	42
Maximum operating temperature (fixed usage)		260°C
Material		Modified PTFE (Polytetrafluoroethylene resin)

Use a tube above the recommended minimum bending radius.
The tubing may be bent if used under the recommended minimum bending radius. Therefore, refer to the tube close bend radius and make sure that the tubing is not bent or flattened.
The tube close bend radius is not guaranteed. The value of 2R is measured with a bent or flattened tube.

How to measure the minimum bending radius

Bend the tubing into a U shape at a temperature of 20°C. Fix one end and close the loop gradually. Measure 2R when the deformed ratio of the tubing diameter at bending reaches 5%.

Maximum operating pressure

Data to be displayed: 30; 45; 60

Part Number
TD1075-10
TD1075-20

Part Number	Standard Unit Price	Minimum order quantity	Volume Discount	Standard Shipping Days ?	Outer Diameter D (Ø)	O.D. [Distinction]	Inner Diameter d (Ø)	I.D. [Distinction]	Minimum Bending Radius (mm)	Bundle winding length (m)	Applicable Tube Size	Maximum operating pressure (MPa)
	293.69 €	1		22 Days	10	Up to 10	7.5	Up to 8	55	10	Metric Size	0.9
	587.40 €	1		4 Days	10	Up to 10	7.5	Up to 8	55	20	Metric Size	0.9

Basic information

Type	Straight	Cutting Service Usage	NA	Material	Fluororesin
Applicable Fluid	Water / Air	Operating Environment	Standard / Chemical Resistance	Color	Blue (Translucent)
Operating temperature(°C)	up to 260

Configure

2Suggestion of an applicable part number.

View Part Numbers

Some specification is not specified yet.

The part number is completed.

Basic Attributes

Outer Diameter D(Ø)
3.18

4

6

6.35

8

9.53

10

12
Clear
O.D. [Distinction]
Up to 4

Up to 5

Up to 6

Up to 7

Up to 8

Up to 10

Up to 15
Clear
Inner Diameter d(Ø)
2.5

4

6

7.5

9
Clear
Bundle winding length(m)
8

10

16

20
Clear
Applicable Tube Size
- Inch Size
- Metric Size
Clear
Maximum operating pressure(MPa)
- 0.9
- 1.4
- 1.6
Clear
Type
- TD
- TID
Clear
I.D. [Distinction]
Up to 3

Up to 4

Up to 6

Up to 7

Up to 8

Up to 9

Up to 10
Clear
Filter by CAD data type
- 2D
- 3D
Clear

Filter by standard shipping days

All

4 Days or Less

22 Days or Less

26 Days or Less

66 Days or Less
Reset

Optional Attributes

For specifications and details, please refer to the catalog.
The specifications and dimensions of some parts may not be fully covered. For exact details, refer to manufacturer catalogs .