Clamp Units (for Manual Tightening)（Page 2）

Shipping Days	All Same day 4 Days or Less 5 Days or Less 6 Days or Less 7 Days or Less 8 Days or Less 9 Days or Less 10 Days or Less 12 Days or Less 14 Days or Less

?* Information on days to ship and prices

• 

  6809P Modular clamp

  AMF

  Modular clamp with swivelling foot, welding version.
  Mechanism can be welded at an angle to it`s support.
  Reamed and case-hardened bearing bushes. Hardened, ground and permanently-lubricated pins. Clamp nuts on lever arm to vary friction in movement.
  Materials: steel, blued. Lever arm made of cast steel, blued. The product is available per 1 peace.

  • Volume Discount

  2D / 3D CAD data available

  Select to compare

  Configure now
  Starting from∗ ：	122.70 €
  Min. Shipping Days ：	5 Days

  *Unit price with basic configuration

• 

  Clamping plates for position indicators / GN 954.6 / B8, B10, B12, B14

  GANTER

  Clamping plates GN 954.6 are used in connection with position indicators GN 954 / GN 9054.
  In a simpler way and without large construction and installation effort these spindles can, after adjustment, be clamped and locked.
  At the same time these plates are fitted with the bore Ø 6,1 to accept the torque limiter for the position indicator.
  The spacer can be installed so that it lies as required either to the right or the left.

  • Volume Discount

  2D / 3D CAD data available

  Select to compare

  Configure now
  Starting from∗ ：	18.12 €
  Min. Shipping Days ：	4 Days

  *Unit price with basic configuration

• 

  Flanged linear actuator connectors, Stainless Steel

  GANTER

  GN 145.1 Stainless Steel-Linear actuator connectors are normally supplied mounted only in connection with a linear actuator and for function control.
  By means of the clamping screw on the guide bore d1 the movement can either be set or the linear actuator connector can be clamped (after setting of final adjustment).
  The standard version of the clamping screw is a socket cap screw with hexagonal socket DIN 912. It can be replaced by a clamping kit GN 911.3 (article code see table of dimensions).

  • Volume Discount

  2D / 3D CAD data available

  Select to compare

  Configure now
  Starting from∗ ：	131.12 €
  Min. Shipping Days ：	7 Days

  *Unit price with basic configuration

• • Promotional pricing

  

  Stainless Steel-Base plate connector clamps / GN 162 / 2-with Stainless Steel-clamping screw DIN 912

  GANTER

  The clamping bores of GN 162 base plate clamps are mechanically machined and designed for construction tubes GN 990 or DIN 2391, DIN 2395 and DIN 2462 respectively.
  The standard version of the clamping screw is a socket cap screw with hexagonal socket DIN 912. It can be replaced by a clamping kit GN 911.3 (article code see table of dimensions).

  • Volume Discount

  2D / 3D CAD data available

  Select to compare

  Configure now
  Starting from∗ ：	45.62 €
  	Special price
  Min. Shipping Days ：	Same day

  *Unit price with basic configuration

• 

  Stainless Steel-Split hubs

  GANTER

  Stainless Steel-Split hubs GN 150 are distinguished by the method of simple clamping to any shaft.
  This can be achieved without prior machining of the shaft, eliminating clamping parts and assembly work.
  A further advantage is the positioning of the lever arm to any required position.
  The shaft tolerance should be within h11; to transmit higher torques the hub can be supplied with a keyway.

  • Volume Discount

  2D / 3D CAD data available

  Select to compare

  Configure now
  Starting from∗ ：	27.98 €
  Min. Shipping Days ：	7 Days

  *Unit price with basic configuration

• 

  Wide base plate connector clamps, Aluminium

  GANTER

  The clamping bores of GN 167 wide base plate connector clamps are not machined and specially designed for construction tubings GN 990 or DIN 2391, DIN 2395 and DIN 2462 respectively.
  The square versions are also suitable for profile systems.
  
  The standard clamping screws are socket cap screws DIN 912. They can be replaced by clamping kits GN 911 (article code see table of dimensions).

  • Volume Discount

  2D / 3D CAD data available

  Select to compare

  Configure now
  Starting from∗ ：	44.84 €
  Min. Shipping Days ：	7 Days

  *Unit price with basic configuration

• 

  Clamping Module, Screw-In Version, Short Design, 6215RP-251

  AMF

  Clamping module, screw-in version, short design
  Pneumatic opening.
  Operating pressure for opening: min. 5 bar - max. 12 bar.
  Housing and piston hardened.
  Repetition accuracy < 0.1 mm.

  2D / 3D CAD data available

  Select to compare

  Configure now
  Starting from∗ ：	238.42 €
  Min. Shipping Days ：	6 Days

  *Unit price with basic configuration

• 

  Clamping Module, Screw-In Version, 6215RP

  AMF

  Clamping module, screw-in version
  Pneumatic opening.
  Opening operating pressure: min. 5 bar - max. 12 bar.
  Housing and piston hardened.
  Repetition accuracy < 0.1 mm.

  2D / 3D CAD data available

  Select to compare

  Configure now
  Starting from∗ ：	208.27 €
  Min. Shipping Days ：	6 Days

  *Unit price with basic configuration

• 

  Surface-Mounted Clamping Module with Pneumatic Opening, 6370AARL

  AMF

  Surface-mounted clamping module
  Pneumatic opening.
  Opening operating pressure: min. 8 bar - max. 12 bar.
  Retensioning operating pressure (turbo): min. 5 bar - max. 6 bar.
  Cover and piston hardened.
  Repeatability < 0.005 mm.

  2D / 3D CAD data available

  Select to compare

  Configure now
  Starting from∗ ：	1,755.67 €
  Min. Shipping Days ：	6 Days

  *Unit price with basic configuration

• 

  Toe clamp high, form B, carbon steel (04482)

  NORELEM

  · Workpiece clamping with positive down force
  
  · Clamping jaws tempered and black oxidised
  
  · Low height, no protruding edges
  
  · Application sector: fixture construction

  Select to compare

  Configure now
  Starting from∗ ：	183.21 €
  Min. Shipping Days ：	4 Days

  *Unit price with basic configuration

• 

  Attachment jaw with prism (41505)

  NORELEM

  · For horizontal clamping of round workpieces
  
  · Can be screwed onto fixed jaws
  
  · Suitable for multi-clamping system

  Select to compare

  Configure now
  Starting from∗ ：	104.88 €
  Min. Shipping Days ：	4 Days

  *Unit price with basic configuration

• 

  Arm Clamp

  NABEYA

  Forged S45C/hardened HRC45 arm clamp.

  Select to compare

  Configure now
  Starting from∗ ：	73.36 €
  Min. Shipping Days ：	5 Days

  *Unit price with basic configuration

• 

  Quick Hold Down Clamp

  NABEYA

  Flat jaw and angled handle for quick hold down clamp (medium).

  Select to compare

  Configure now
  Starting from∗ ：	330.25 €
  Min. Shipping Days ：	5 Days

  *Unit price with basic configuration

• 

  Bar for Quick Lock

  NABEYA

  [Features]
  · Bar for Quick Lock.
  · Annoying thread feeding when clamping is not necessary.
  · A one-action clamp that adopts a cam lock mechanism

  Select to compare

  Configure now
  Starting from∗ ：	53.81 €
  Min. Shipping Days ：	7 Days

  *Unit price with basic configuration

• 

  Clamp Part of Wedge Clamp (for T-Shaped Grooves)

  NABEYA

  For the T-slot on the clamping part of the wedge clamp set. Compatible T-groove 14 mm to 22 mm, clamp stroke 6 mm. The workpiece contact surface is a flat type. The manufacturer also sells the clamp part only.

  Select to compare

  Configure now
  Starting from∗ ：	195.85 €
  Min. Shipping Days ：	7 Days

  *Unit price with basic configuration

• 

  Wedge Clamp Set (for T-Shaped Grooves)

  NABEYA

  Wedge clamp set for T-grooves, flat type.

  Select to compare

  Configure now
  Starting from∗ ：	320.13 €
  Min. Shipping Days ：	5 Days

  *Unit price with basic configuration

• 

  Swing Clamp Holder S Type

  NABEYA

  An inexpensive, compact clamp. The free swivel makes it easy to attach and detach workpieces.

  Select to compare

  Configure now
  Starting from∗ ：	26.83 €
  Min. Shipping Days ：	5 Days

  *Unit price with basic configuration

• 

  Swing Clamp Height Adjusting Support

  NABEYA

  Of course, it can also be used for height adjustment in fixing workpieces. It can be used for both T-grooves and tap holes.

  Select to compare

  Configure now
  Starting from∗ ：	102.02 €
  Min. Shipping Days ：	5 Days

  *Unit price with basic configuration

• 

  Double Swing Clamp S Type

  NABEYA

  This product can clamp 2 workpieces at the same time. Due to its compact structure (cylinder diameter 10 mm to 30 mm), it can be used in small spaces. The freely rotating structure saves time when loading and unloading the workpieces.

  Select to compare

  Configure now
  Starting from∗ ：	84.55 €
  Min. Shipping Days ：	5 Days

  *Unit price with basic configuration

• 

  Toe Adjusting Clamp TCH Type

  NABEYA

  Tightening is performed while pressing the movable part downward, preventing the workpiece from lifting.

  Select to compare

  Configure now
  Starting from∗ ：	312.30 €
  Min. Shipping Days ：	7 Days

  *Unit price with basic configuration

• 

  Toggle Side Clamp 6844

  NABEYA

  6844: SS400/6844NI: SUS304/6844: Zinc-plated toggle side clamp 6844.

  Select to compare

  Configure now
  Starting from∗ ：	188.19 €
  Min. Shipping Days ：	7 Days

  *Unit price with basic configuration

• 

  Base Unit 7110F

  NABEYA

  It is the base part of the Clamp Unit 7110 series. By combining various parts (spacers and supports), the height can be adjusted to suit the workpiece.

  Select to compare

  Configure now
  Starting from∗ ：	548.14 €
  Min. Shipping Days ：	7 Days

  *Unit price with basic configuration

• 

  Base Unit 7110FA

  NABEYA

  It will be the base part of the Clamp Unit 7111 series. By combining various parts (spacers and supports), the height can be adjusted to suit the workpiece.

  Select to compare

  Configure now
  Starting from∗ ：	1,019.75 €
  Min. Shipping Days ：	7 Days

  *Unit price with basic configuration

• 

  Hold Clamp, Stopper

  NABEYA

  Includes a hex wrench. Completely tightened with a sliding mechanism. Saves time thanks to its "one point" fitting and removal function. For machining the whole top surface of the workpiece and through-hole machining. Fully heat-treated for semi-permanent use. A workpiece rising prevention mechanism type.

  Select to compare

  Configure now
  Starting from∗ ：	190.51 €
  Min. Shipping Days ：	7 Days

  *Unit price with basic configuration

• 

  Hold Clamp Set

  NABEYA

  Includes a hex wrench. Completely tightened with a sliding mechanism. Saves time thanks to its "one point" fitting and removal function. For machining the whole top surface of the workpiece and through-hole machining. Fully heat-treated for semi-permanent use. A workpiece rising prevention mechanism type.

  Select to compare

  Configure now
  Starting from∗ ：	329.87 €
  Min. Shipping Days ：	7 Days

  *Unit price with basic configuration

• 

  Mini Low Height Clamp

  NABEYA

  With wrench operation from the side, the jaw is locked in the downward direction, and the workpiece does not rise up.

  Select to compare

  Configure now
  Starting from∗ ：	198.36 €
  Min. Shipping Days ：	7 Days

  *Unit price with basic configuration

• 

  Universal Clamp

  NABEYA

  It can steplessly fasten tall and short workpieces.

  Select to compare

  Configure now
  Starting from∗ ：	110.57 €
  Min. Shipping Days ：	5 Days

  *Unit price with basic configuration

• 

  Rubber Cap 6893

  NABEYA

  Dedicated clamping screw for toggle clamps.

  Select to compare

  Configure now
  Starting from∗ ：	6.35 €
  Min. Shipping Days ：	5 Days

  *Unit price with basic configuration

• 

  Clamp Part of Wedge Clamp (for Tapped Holes)

  NABEYA

  The workpiece is prevented from rising up by being fastened downward. Ideal for machining through holes.

  Select to compare

  Configure now
  Starting from∗ ：	125.60 €
  Min. Shipping Days ：	5 Days

  *Unit price with basic configuration

• 

  Side Clamp Jack

  NABEYA

  It serves as the base for clamping the side of large-scale processing machine workpieces. Compatible with workpiece contact side tapped hole M 20 / Table mounting side slotted hole structure allows fine adjustment

  Select to compare

  Configure now
  Starting from∗ ：	150.00 €
  Min. Shipping Days ：	7 Days

  *Unit price with basic configuration

• 

  Side Jack B Type

  NABEYA

  [Features]
  · Simply insert into the T-groove.
  · Useful for receiving cutting resistance from the side.
  · The tap hole opening is horizontal to the table. With stopper bolt.

  Select to compare

  Configure now
  Starting from∗ ：	89.39 €
  Min. Shipping Days ：	7 Days

  *Unit price with basic configuration

• 

  Side Jack E Type

  NABEYA

  [Features]
  · Simply insert into the T-groove.
  · Useful for receiving cutting resistance from the side.
  · Especially for large processing machines

  Select to compare

  Configure now
  Starting from∗ ：	343.67 €
  Min. Shipping Days ：	7 Days

  *Unit price with basic configuration

• 

  Side Jack F Type

  NABEYA

  [Features]
  · Simply insert into the T-groove.
  · Useful for receiving cutting resistance from the side.
  · Especially for large processing machines. Cutting resistance is received with greater strength by clamping the step part

  Select to compare

  Configure now
  Starting from∗ ：	371.60 €
  Min. Shipping Days ：	7 Days

  *Unit price with basic configuration

• 

  Start Element 7110FT

  NABEYA

  S45C / quenched base unit low type (for T slot).

  Select to compare

  Configure now
  Starting from∗ ：	339.86 €
  Min. Shipping Days ：	7 Days

  *Unit price with basic configuration

• 

  Double Swing Clamp Set S Type

  NABEYA

  This product can clamp 2 workpieces at the same time. It has a compact structure and can be used in small spaces. The freely rotatable structure saves time in loading and unloading workpieces.

  Select to compare

  Configure now
  Starting from∗ ：	107.34 €
  Min. Shipping Days ：	5 Days

  *Unit price with basic configuration

• 

  Toe Adjusting Clamp

  NABEYA

  [Features]
  · Tightening is performed while pressing the movable part downward, preventing the workpiece from lifting.
  · Lifting prevention (generates force in the downward direction).
  · Ideal for thin workpieces.
  · Dovetail groove can withstand lateral force.
  · Free Mounting Position

  Select to compare

  Configure now
  Starting from∗ ：	427.55 €
  Min. Shipping Days ：	7 Days

  *Unit price with basic configuration

• 

  Toggle Down Clamp 6800

  NABEYA

  [Features]
  · 6800: SS400/6800NI: SUS304, 6800: Zinc-plated toggle-down clamp 6800.
  · 6800S: The structure prevents operation unless holding the safety lever, preventing erroneous operation and malfunction.

  Select to compare

  Configure now
  Starting from∗ ：	72.64 €
  Min. Shipping Days ：	5 Days

  *Unit price with basic configuration

• 

  Toggle Down Clamp 6803

  NABEYA

  [Features]
  · SS400 and galvanized toggle down clamp 6803.
  · 6803S: Since it has a structure where it cannot be operated unless the safety lever is gripped, it prevents error operation and malfunction.

  Select to compare

  Configure now
  Starting from∗ ：	99.55 €
  Min. Shipping Days ：	5 Days

  *Unit price with basic configuration

• 

  Toggle Hook Clamp 6848V

  NABEYA

  6848VNI is made of stainless steel. The hook length can be adjusted.

  Select to compare

  Configure now
  Starting from∗ ：	108.98 €
  Min. Shipping Days ：	5 Days

  *Unit price with basic configuration

• 

  Hold Clamp, Clamp

  NABEYA

  Includes a hex wrench. Completely tightened with a sliding mechanism. Saves time thanks to its "one point" fitting and removal function. For machining the whole top surface of the workpiece and through-hole machining. Fully heat-treated for semi-permanent use. A workpiece rising prevention mechanism type.

  Select to compare

  Configure now
  Starting from∗ ：	284.99 €
  Min. Shipping Days ：	7 Days

  *Unit price with basic configuration

• 

  Low Edge Clamp (Double Sided Type)

  NABEYA

  It is a compact clamp that does not lift much. Ideal for machining thin, low-profile objects. There are three sizes of tightening bolts: M4, M6, and M12. It has a compact size and large stroke of 0.3 to 1.1. The guide groove of the main body shortens workpiece setup time (excluding LWC4). It has a structure that prevents chips from entering inside.

  Select to compare

  Configure now
  Starting from∗ ：	35.73 €
  Min. Shipping Days ：	7 Days

  *Unit price with basic configuration

• 

  Heavy Duty Toggle Side Clamp 6842PL

  NABEYA

  Can be used for either pushing or pulling. Clamping screw and rubber cap attached.

  Select to compare

  Configure now
  Starting from∗ ：	188.63 €
  Min. Shipping Days ：	7 Days

  *Unit price with basic configuration

• 

  PA Feed Plate for Quick Lock

  NABEYA

  Parts for quick lock. Quick Lock is a one-action clamp product that does not feed screws. Reduces troublesome hand tighten work time. Each part is also sold separately.

  Select to compare

  Configure now
  Starting from∗ ：	22.27 €
  Min. Shipping Days ：	7 Days

  *Unit price with basic configuration

• 

  Adjustment Bolt for Quick Lock

  NABEYA

  Parts for quick lock. Quick Lock is a one-action clamp product that does not feed screws. Reduces troublesome hand tighten work time. Each part is also sold separately.

  Select to compare

  Configure now
  Starting from∗ ：	53.81 €
  Min. Shipping Days ：	7 Days

  *Unit price with basic configuration

• 

  Oil Cup for Quick Lock

  NABEYA

  Parts for quick lock. Quick Lock is a one-action clamp product that does not feed screws. Reduces troublesome hand tighten work time. Each part is also sold separately.

  • Volume Discount

  Select to compare

  Configure now
  Starting from∗ ：	5.47 €
  Min. Shipping Days ：	9 Days

  *Unit price with basic configuration

Loading...