- inCAD Library Home
- > No.000123 Multiple Lead Forming Jig
No.000123 Multiple Lead Forming Jig
24
24
Workpiece retention and forming by two toggle clamps.
Related Category
Toggle clamps
| Product name | PushPull |
|---|---|
| Part number | MC07-3 |
| Features | Suitable when clamping a workpiece from the side. |
* Orange colored cells in the table below indicate the part numbers used in this example.
Selection criteria
Clamping force at the end of the stroke is suitable for the application.
Available sizes
■Toggle Clamps -Push-Pull-
| Material | EN 1.0038 Equiv. |
|---|---|
| Surface Treatment | Main Body: Trivalent Chromate / Shaft: Nickel Plating |
| Stroke (mm) | 30 |
| Tightening Force (N) | 1960 |
| Weight (g) | 370 |
| Open-Close Angle of Handle | 140° |
| Overall Width | 50 |
| Overall Height (Clamped) | 99.5 |
| Tip Bolt | Steel Bolt |
| Overall Length (Clamped) | 158.5 |
| Overall Length (Unclamped) | 265 |
| Push Shaft Height | 20 |
* Please see the product pages for shape details and dimensions.
Adjustment Pads
| Product name | Adjustment Pads/Nonslip Type |
|---|---|
| Part number | FJGMS10-75-R |
| Features | The rubber material on pads securely grips on the floor surface. |
* Orange colored cells in the table below indicate the part numbers used in this example.
Selection criteria
Select the non-slip type to prevent slipping during operation.
Risk info.
Insufficient for anti-slip effect.
Available sizes
■Adjustment Pads - Nonslip Type
| Main Body | Rubber | |||
|---|---|---|---|---|
| Material | Surface Treatment | Material(Color) | Hardness | |
| Steel Type | EN 1.0038 Equiv. | Trivalent Chromate | Elastomer (Black) | - |
| Neoprene Rubber (Black) | Shore A70 | |||
| Non-Migration Chloroprene Rubber (Gray) | ||||
| Electrically Conductive Rubber (Black) | ||||
| PVC (Dark Blue) | ||||
| Stainless Steel | EN 1.4301 Equiv. | Electrolytic Polishing | Elastomer (Black) | - |
| Neoprene Rubber (Black) | Shore A70 | |||
| Non-Migration Chloroprene Rubber (Gray) | ||||
| Electrically Conductive Rubber (Black) | ||||
■Sizes and Dimensions.
| Thread DIA. | Thread Length (mm). |
|---|---|
| 8 | 50, 100 |
| 10 | 75, 100 |
| 12 | 75, 100, 125, 150 |
| 16 | 75, 100, 130, 150, 180 |
| 20 | 100, 130, 150, 180 |
Performance info
■Speeds / Loads (Load Info.) of Adjustment Pads
| Thread DIA. | Thread Length (mm) | Allowable Vertical Load (kN) |
|---|---|---|
| 8 | 50 | 3.9 |
| 100 | ||
| 10 | 75 | 4.3 |
| 100 | ||
| 12 | 75 | 4.9 |
| 100 | ||
| 125 | ||
| 150 |
-
-
TERMS AND CONDITIONS FOR USE OF CAD DATA-
Your access to the CAD data that MISUMI Corporation (hereinafter referred to as the Company) posts on this site (including 3D CAD data, intermediate 3D CAD data and 2D CAD data; hereinafter referred to as the Data) are of products manufactured and/or sold by the Company (hereinafter referred to as the Products) assumes that you have read and accepted these terms and conditions which govern your use of the Data. If you do not agree to these terms and conditions, you must stop using this website and the Data. You must not use the Data for any unlawful purpose or in any manner inconsistent with these terms and conditions.
- 1. CAD Data
- The Data is prepared for assisting the Company's users in the CAD design process by providing dimensions and other Product information. In order to provide the best speed and stability working within this site, the Product drawings were simplified to reduce the size of the Data. For instance, some of the Products are shown without the oil groove shape, screws or spring shape. Also, please be aware that the tolerance, surface roughness and/or chamfer of the Data may vary from the actual Products.
- 2. Disclaimer on Data
- While the Company has carefully prepared the Data, accuracy of the Data is not guaranteed and is subject to the variances as described above. The Company may also modify, add or delete the Data at any time without prior notice. The Company assumes no liability for any direct, indirect, consequential or special damages that you may claim resulted from your use of the Data or any changes to or deletions of the Data regardless of the reason. The Company provides no warranty as to the quality, accuracy, functionality, safety or reliability of the combination of Products and parts. Example applications and combinations of the Products are provided for illustrative purposes only.
- 3. Copyright
-
Copyrights to the content and the Data belong to the Company or the manufacturers of the Products. The said copyright is protected by the Copyright Act and international treaties. The use (including duplication, modification, uploading, posting, transmission, distribution, licensing, sales and publishing) of the Data except for the purpose to use the Data described above without prior approval of the Company is not allowed. The Data cannot be used for any purposes (including sales promotion) except for designing your machine. If you violate this provision or the laws or regulations, the Company may prohibit you from the use of the Data, the Company’s site and/or take legal action. So long as you comply with these terms and conditions, the Company grants to you a non-exclusive, non-transferable, revocable license to access and use the Data for the sole purpose of assisting you in designing machines that incorporate products.
- 4. Disclaimer of Warranty
- ANY AND ALL CONTENT APPEARING ON THIS WEB SITE IS PROVIDED FOR INFORMATIONAL PURPOSES ONLY. THIS WEB SITE, ITS CONTENT AND ITS LINKS ARE PROVIDED ON AN "AS IS" AND "AS AVAILABLE" BASIS AND ARE USED ONLY AT YOUR SOLE RISK, TO THE FULLEST EXTENT PERMISSIBLE BY LAW. THE COMPANY DISCLAIMS ALL WARRANTIES, EXPRESS OR IMPLIED, OF ANY KIND, REGARDING THIS WEB SITE (INCLUDING ITS CONTENT, HARDWARE, SOFTWARE AND LINKS), INCLUDING AS TO FITNESS FOR A PARTICULAR PURPOSE, MERCHANTABILITY, TITLE, NON INFRINGEMENT, RESULTS, ACCURACY, COMPLETENESS, ACCESSIBILITY, COMPATIBILITY, SECURITY AND FREEDOM FROM COMPUTER VIRUS. THE COMPANY WILL NOT BE LIABLE FOR ANY DAMAGES OR LOSSES, INCLUDING DIRECT, INDIRECT, CONSEQUENTIAL, SPECIAL, INCIDENTAL OR PUNITIVE DAMAGES AND/OR LOST PROFITS, IN CONNECTION WITH USE OF THE INTERNET, THIS WEB SITE, ITS CONTENT OR ITS LINKS
Further, the Company will not be liable to you for any failure or delay by the Company to provide access to the Data or any of its obligations under these terms and conditions where such failure or delay is the direct or indirect result of any circumstances beyond the Company's reasonable control (and the Company's obligations will be suspended for the duration of such circumstances). - 5. Policy of Third Parties
- You may be required to separately agree to third party's policies if you use third party software to create or browse the Data or use a third party’s CAD data. In this case, the Company does not assume any responsibility for defects of such CAD data or the software of the third party or violation of their rights. Understand them before use.
CAD Data Download (Unit Assembly)
CAD Data Download: File Format
Cautions on the CAD data
-
Assembly data shows the assembly drawings in the concept design phase. The sole purpose of the data is to explain the structure and functionality of the assembly and is not considered nor to be used as a final design.
You will need to edit the Data so that it meets your specific design conditions. -
The CAD data unit assembly consists of sub-assemblies.
Each sub-assembly unit can be used as it is or can be edited. - The Data for fabricated parts is based on easy-to-edit dimensions and shapes in sketches and histories.
- The Data including the third-part components are made by the Company.
* The part in the frame is a sub-assembly unit.
-
Your access to the CAD data that MISUMI Corporation (hereinafter referred to as the Company) posts on this site (including 3D CAD data, intermediate 3D CAD data and 2D CAD data; hereinafter referred to as the Data) are of products manufactured and/or sold by the Company (hereinafter referred to as the Products) assumes that you have read and accepted these terms and conditions which govern your use of the Data. If you do not agree to these terms and conditions, you must stop using this website and the Data. You must not use the Data for any unlawful purpose or in any manner inconsistent with these terms and conditions.
-
- * Unit assembly CAD data consists of some sub-assemblies.
Each sub-assembly unit can be used as it is or can be edited.
Application Overview
Purpose
- Jig to clamp and form multiple workpieces at the same time.
Points for use
- Manual mechanism by toggle clamp operations.
- Cover for the workpiece is designed to be removed without using tools.
Target workpiece
- Electronic part.
- Outer dimensions: W9.5 x D6 x H35.
Design Specifications
Operating Conditions or Design Requirements
- Outer dimensions: W276 x D231 x H144.
- Toggle clamp stroke:
Workpiece clamp side: 40mm.
Forming side: 30mm.
Required Performance
- Assumed forming load: 200N.
Selection Criteria for Main Components
- Toggle clamp.
- As the toggles make horizontal movements, a side push type is selected.
- For the toggle clamp for the workpiece clamp, a push-pull type is selected because the clamp handle needs to be in horizontal position during clamping.
- Leveling mount.
- Non-slip type leveling mounts are selected to prevent the jig from slipping during work.
Design Evaluation
Verification of main components
- Verify that selected toggle clamp tightening force is appropriate for lead forming.
- Toggle clamp for forming.
- Assumed forming load: 200N.
(This is an estimated value because the load changes depending on the lead wire diameter, bending position, material, etc.) - Toggle clamp tightening force: 1960N.
- Safety factor: 1960/200 = 9.8times.
(As the load is an estimated value, a large safety factor should be taken into consideration.).
- Assumed forming load: 200N.
Other Design Consideration
- Multiple workpieces are clamped altogether by one clamp and formed by the other clamp.
- To clarify the order of toggle clamp operations, the operation numbers are indicated by stickers attached to the clamps.
- The shape of the workpiece escape in the base block is made smaller to eliminate unacceptable workpieces (bent workpieces).
- The vertical clearance for the lead forming part should be equal to or above the lead wire diameter in size and made as narrow as possible (in consideration of the upper and lower limits of tolerance).
- To prevent the jig from shifting during workpiece retention and forming, leveling mounts with rubber are used.
Explore Similar Application Examples
Page
-
/
-
Payment Method
On-Demand Manufacturing
Certificates
Copyright © MISUMI Corporation All Rights Reserved.